Differences

This shows you the differences between two versions of the page.

--- control:programs [2022/11/25 12:50] – marilisebester_gmail.com
+++ control:programs [2023/04/11 06:53] (current) – marilisebester_gmail.com
@@ Line 1: / Line 1: @@
 ====== Control - Programs ======
+=====Trouble Shooting=====
+====Two programs with the same Mainline running====
+Farmsync cannot run two programs using the same Mainline simultaneously. Both programs will start, but they will not be able to stop.
+To set this right, the system must be reset. Please contact a Farmsync Technician to assist.
+In order to prevent this from happening again, please make use of the Priority Function under the "Scheduling" heading in the Program.
+How does the Priorities work:
+  * Select the relevant Mainline from the dropdown list.
+  * Enter a priority from 1 to 10, 1 being the highest & 10 being the lowest.
+  * Farmsync will give priority to the program with the highest priority rating.
+    * Any program currently running & that has a lower priority rating will be paused,
+    * & the higher priority program will be allowed to run until the runtime is complete,
+    * after which the program that was paused will be resumed.
+====Program shows running but physical equipment is offline====
+This usually occurs with Pump Start Units, or systems "Piggy-backing" off external internet systems.
+  * Refresh the station connected to the Program
+    * If program still shows "Running", it is a hardware issue
+  * Take a video of the controller lights & send to a Farmsync Technician for further assistance
+=====Control Screen=====
 {{ :control:control_program_control.png?nolink&600 |}}
@@ Line 9: / Line 37: @@
   * **E:** Total Runtime (minutes)
-{{ :control:control_program_functions.png?nolink&400 |}}
+{{ :control:control_program_functions.png?nolink&400|}}
+====Program Control====
   * **A:** "Play" - Press this button to start the program
   * **B:** "Pause" - Press this button to pause the program
@@ Line 16: / Line 44: @@
   * **D:** "Settings / Gear Icon" - Press this button to enter the setup page for the specified program
   * **E:** "Synchronize Station" - Should it appear as if the readings of the sensors are not updating, press this button to refresh
+=====Control Display=====
-===== Steps =====
+==== Steps ====
 Clicking the arrow button on the left side of the program name will expand the program to view more detail:
@@ Line 45: / Line 73: @@
           * EC
-===== Flow Control =====
+==== Flow Control ====
+To the right, you will be able to see the above "Expected" & "Actual Flow Rates" of the program.
 {{ :control:control_program_control2.png?nolink&400 |}}
-To the right, you will be able to see the above "Expected" & "Actual Flow Rates" of the program.
-===== Sensors =====
+==== Sensors ====
+All the sensors connected to the Controller active during this program will be listed to the right, along with their values.
 {{ :control:control_program_contro32.png?nolink&400 |}}
-All the sensors connected to the Controller active during this program will be listed to the right, along with their values.
-===== Pump Details =====
-{{ :control:control_program_control4.png?nolink&400 |}}
+==== Pump Details ====
+{{ :control:control_program_control4.png?nolink&400|}}
 The above will be displayed for each pump on the program.
   * Pump Program Name
@@ Line 65: / Line 94: @@
   * Flow Rate (m3/h)
-===== Fertilizer Details ======
+==== Fertilizer Details =====
-{{ :control:control_program_control5.png?nolink&400 |}}
+{{ :control:control_program_control5.png?nolink&400|}}
 The above will be displayed for each fertilizer on the program.
   * Fertilizer Program Name