Differences

This shows you the differences between two versions of the page.

--- programs:pump_programs [2022/12/05 06:29] – marilisebester_gmail.com
+++ programs:pump_programs [2023/01/16 08:08] (current) – [Trigger] marilisebester_gmail.com
@@ Line 19: / Line 19: @@
   * **G:** Enter the duration of time to pass before the pump starts after being told to start
   * **H:** Enter the time in seconds that the pump must stop before the Runtime is finished
-  * **I:** Enter the min Start Pressure (Bar)
+  * **I:** *Enter the min Start Pressure (Bar)
-  * **J:** Enter the pressure (Bar) to stop the Bleed
+  * **J:** *Enter the pressure (Bar) to stop the Bleed
-=====Sensor Details=====
+=====Sensor Details*=====
 {{ :programs:pump_program_sensor_details.png?nolink&400|}}
@@ Line 29: / Line 29: @@
   * **A:** Select the relevant Control Valve from the dropdown list (only if there is one, leave as "Not Set" if there is no Control Valve)
   * **B:** Enter a Delay (seconds) before the Control Valve opens after the start of the pump
+      * If the valves are closed when the pump is started, it means that there is no discharge head & minimum resistance to the pump, and therefore the output current is the smallest.
+      * Although the current is greater than the normal value when the motor starts, closing the discharge valve of a pump can avoid additional load on the pump.
   * **C:** Select the relevant Current Sensor from the dropdown list
   * **D:** Select the relevant Pressure Sensor from the dropdown list
@@ Line 54: / Line 56: @@
-=====Alarms=====
+=====Alarms*=====
 {{ :programs:pump_program_alarmsrev.png?nolink&400|}}
@@ Line 71: / Line 73: @@
 =====Trigger=====
+The values entered here are based on the type of sensor selected as a trigger. E.g. if the selected trigger is a pressure sensor, the min / max values would be related to pressures (either in Bar or meters); if the selected trigger is a Current Sensor, the min / max values would be in Amps.
 {{ :programs:trigger.png?nolink&400|}}
-  * **A:**
+  * **A:** Select a trigger sensor
-  * **B:**
+  * **B:** Enter a min Threshold
-  * **C:**
+  * **C:** Enter a max Threshold
-  * **D:**
+  * **D:** Enter a max interval
-  * **E:**
+  * **E:** Enter a min Active time for the trigger
-  * **F:**
+  * **F:** Select a trigger type from the dropdown list
+=====Input / Output=====
+{{ :programs:pump_program_i-o.png?nolink&400|}}
+  * **A:** Select the relevant port connected to the Bleeding System (Usually a small pump or electric valve or both)
+  * **B:** Select the relevant port connected to the Main Pump (Used when pump use to be started by hand / green button)
+  * **C:** Select the relevant port connected to the Main Pump (Should be the "PC" connection on the starterbox)
+  * **D:** Select the relevant port connected to the Main Pump (Used when pump use to be started by hand / red button)
+  * **E:** Select the relevant port for the Actuator valve if applicable
+  * **F:** Select the relevant port for the Actuator valve if applicable
+=====Events=====
+{{ :programs:pump_program_events.png?nolink&400|}}
+  * **A:** Select from the dropdown list a program that must be started along with this Valve Program
+  * **B:** Select from the dropdown list a program that must be started once this Valve Program has stopped
+=====Rate Control=====
+{{ :programs:pump_program_rate_controlrev.png?nolink&400|}}
+  * **A:** Enter the Target Pressure (Bar) / Desired Pressure
+  * **B:** Enter the Target Amps / Desired Amps
+  * **C:**
+  * **D:**
+  * **E:**
+  * **F:** “Rate Control Method”:
+      * "Analog VSD Output"
+      * "Actuator Control"
+      * "Digital Out Setpoint"
+  * **G:**
+  * **H:**
+  * **I:**
+  * **J:**
+=====Pump Cluster=====
+{{ :programs:pump_program_pump_cluster.png?nolink&400|}}
+  * **A:**
+  * **B:**
+  * **C:**
+  * **D:**
+  * **E:**
+  * **F:**
+  * **G:**
+  * **H:**
+  * **I:**
+  * **J:**
+  * **K:**
+  * **L:**
+  * **M:**
+  * **N:**
+  * **O:**
+  * **P:**