=====Filter Program=====

Please note that to create a filter program, the following must be created first:
  * "Filter" Mainline - created under setup_mainlines
  * Valves for each of the backflush valves on the filter station - created under setup_manage valves
  * DP (Differential Pressure) sensor - created under setup_all sensors
Should you require help in creating these, please contact your Farmsync Technician

=====Creating a Filter Program=====
{{ :programs:program_details1.png?nolink&400 |}}
  * A: “Name” – Enter a name for the Filter Program
  * B: “External Reference” – For Farmsync internal use only
  * C: “Station” – Select the relevant station that the filter is connected to from the dropdown list

Press "Save" in order to set the rest of the settings for this program

{{ :programs:program_details2.png?nolink&400 |}}
  * A: “Enabled Automatic Start”
    * It is important to note that if this function is ticked, the Flush program will run permanently, meaning even when no Valve program is running
    * If this option is taken, DO NOT add the Filter Flush program to a Valve Program, as this will cause a clash
    * If you want the Filter Flush program to run ONLY when the valve program is running, then this function must NOT be ticked
  * B: “Stop Remote Flush program when flushing done” – under construction
  * C: “Total Program Run Time (minutes)” – Enter the max Runtime (min) for the flush program
  * D: “Flush Duration (seconds)” – Enter the time duration (sec) allowed for each filter to flush 
  * E: “Flush Time Duration (seconds)” – Enter the time allowed between filters to pass before the next filter flushes
  * F: “Minimum duration between flush operations (seconds)” – Enter the min time duration between flush cycles
  * G: “Min Pressure to enable pressure flush (Bar)” – Enter the min pressure difference between in & outlet of filter allowed before filter flushes
  * H: “Min Pressure to enable time flush (Bar)” – Enter the min pressure the system must supply for flushing to occur (refer to supplier filter specifications)
  * I: “Pressure Flush Delay (seconds)” – Enter the time (sec) allowed to pass for pressure difference to be higher than min before flush is enabled
  * J: “Flush Duration Delay (seconds)” – enter the duration of time that must past from when flushing is triggered before the flushing valves open (eg. allows time for Mainvalve to close)
  * K: “Flush on Start” – When enabled, filter will flush when program starts
  * L: “Flush on End” – When enabled, filter will flush when program stops
  * M: “Filter Start Delay (seconds)” – Duration of time allowed to pass after filter program has started before filter flushes

See below example of flush program times explained:
{{ :programs:1flush_timing.png?nolink&600 |}}
{{ :programs:flush_timing.png?nolink&600 |}}

{{ :programs:program_details3.png?nolink&400 |}}
  * A: “Flush Activated Sensor” – 
  * B: “Flush Active Port” – 
  * C: “Before Filter or Differential Pressure Sensor” – Select the relevant Pressure Sensor / DP Sensor from the dropdown list
  * D: “After Filter Pressure Sensor” – Select the relevant Pressure Sensor from the dropdown list (if DP Sensor was selected in C, then this sensor can be left to "Not Set"
  * E: “Remote Flush Program to Start when Flushing” – 
  * F: “Remote Pause / Resume program when flushing” – Select the relevant program that must be paused if the flushing sequence is initiated, this program will resume once the flushing program is completed
  * G: “Mainline Control Valve” – Select the relevant Mainline Control Valve from the dropdown list, should one be present
  * H: “Mainline Control Valve Close Delay” – Enter the duration of time allowed to pass from when filter flush is initiated before the Mainline Control Valve must close
  * I: “Master Filter Program” – Select the relevant Filter program from the dropdown list
  * J: “Auto Start from Master Filter Program” – Enable if current filter program must start the same time as the Master Filter Program

=====Flush Valves=====
{{ :programs:flush_valves.png?nolink&400 |}}

Choose from the dropdown lists below the relevant Flush Valves that were created for the Filter under “Setup_Manage Valves”; Provision has been made for 32 valves in total.